cutting off porch plank floor

  • Step 3. illustration of cutting the first row of boards to more generously accomodate last row. Finally, calculate the width of the last row. If it will be less than 1/3 of a plank, cut about 1/3 of the plank off the first row for even starting and finishing rows.


  • If your hardwood floor is in generally fine shape, with only a damaged spot or two, it is easy and economical to make small repairs by replacing a strip or plank of flooring. You can also fix buckled areas of flooring and avoid having to completely refinish your floors. Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as& ...


  • Answers to the most common questions about laminate flooring. ... Because laminate flooring is a wood flooring product it is not recommended that laminates be installed in wet locations such as bathrooms, washrooms, saunas, enclosed porches or verandas, or anywhere that may require wet-mopping. ... In an average installation, approximately 7% to 10% of the total area to be covered will be wasted for several reasons, typically cuts, planks damaged during installation, or errors.


  • Photo 3: Prepare the new plank. Saw off the bottom groove on the new flooring plank. Rip cut and remove the bottom groove from the replacement flooring piece using a table saw, circular saw, or sharp chisel and utility knife. Set the saw fence to cut 5/16 in. off the width of the plank and the saw blade depth to cut into it 1/4 in. deep. Once the bottom groove has been removed, measure the length required for the replacement piece and cut it. Pencil the location of floor joists on the new& ...


  • Make sure to always cut the wall end of the wood so that you do not cut off the groove that fits to the tongue. If that happens, that would result in a pretty big gap. Find a piece and lay it alongside the hole and flip it over. Make sure when you make the mark to cut off the wall side, not the room side. When you make the mark, butt it up against the baseboard and then mark at the end of that tongue. That will leave a 3/8" gap for expansion and contraction when installing the piece.


  • 4. Craft a Cabinet Door. kitchen cabinet with glass panels, 10 uses for wood flooring scraps. View as slideshow. Photo by Kolin Smith. Use unfinished planks, with the tongues cut off, for the stiles and rails and plywood or glass for the panel. Arrange the boards groove-side in to capture the panel, then secure with glue and screws. 6 ×& ...


  • Should an individual plank or tile be doubtful as to appearance or dimension the installer should not use this piece. USfloors will send replacement in a timely fashion. NOTE: USfloors COREtec Plus floors may be installed with a direct .... For plank installations, when cutting the last plank in a row to fit, you can use the cut-off end to begin the next row. If cut-off end is less than 8”, discard it and instead cut a new plank at a random length (at least 8” in length) and use it to start the next& ...


  • I could either cut them down, install them, and then sand them down like a normal wood floor…. or I could rent this big flooring sander, knock each sheet out about a minute or two, and then cut them down into planks and install. That thing was a heavy beast, but it worked great. And it was only about $50 bucks for a 3 hour rental from Menards. I decided to go this route, because I also wanted to slightly round off the plank edges with my palm sander before installing& ...


  • Install the planks with the tongue side facing the wall (some manufacturers recommend you cut off the tongue edge of planks that face walls). Connect one plank to another by connecting the tongues and grooves. You may be able to snugly connect the planks by hand, or you may need to use a pull bar from the installation kit and a hammer to pull them together or a tapping block to tap the joints together. Cut the last plank in the row to length (save the scrap if it's at least 12 inches& ...


  • How to replace weathered, rotting outdoor flooring. ... Replacing porch decking is not a challenging task for any homeowner who's used a circular saw and a table saw, particularly if you have replacement boards milled to the same width as the originals. Just resist the temptation to cut out only the damaged areas. Short patches leave .... joist on the faces of the neighboring boards. Then cut off the bottom edge of the last board's groove so it can rest on top of the last exposed tongue.


  • by Joanna Swanson, Demand Media porch flooring is exposed to the elements and over time will become damaged. ... Circular saw Rotary tool with cutting and sanding accessories 1-inch demolition chisel Pry bar Hammer 5-in-1 scraping tool Decking boards Table saw Oil-based primer Construction adhesive Ring-shark sliding nails Nailset Sander Oil-based paint ... With a table saw, cut off the bottom part of the groove so that it will sit on top of the tongue of the old flooring.


  • Tools: 16-gauge finish nailer; table saw; circular saw; random orbital sander (with 240-grit pads); mitre saw for cutting planks to length/angle cuts (optional). plywood plank flooring. Note: There are many tutorials about how to install a plywood plank floor; however, I thought I'd include how we did it since it's different than many I looked at online. 1. Make the planks: Start off by cutting a sheet of plywood in half width-wise. To do this, either set the sheet down on top of& ...


  • Cut off the Excess. removing the excess of a herringbone pattern floor with a circular saw. Photo by Wendell T. Webber. Screw a strip of molding or other material to a narrow length of plywood, place the fence of a circular saw against the strip, and rip the plywood to create a long cutting guide for the saw. Line up the guide over the tape and, using spacers, screw it to the subfloor where it extends past the installed flooring. Set the circular saw on the guide, and adjust the depth of the& ...


  • Hardwood floor Layout How to Cut & Fasten Hardwood flooring Laying the First Rows of a Wood floor Completing a Wood floor Installation. Expert advice on how to install hardwood floors from start to finish, including tools and ..... Remove any spacers, cut off excess underlayment that may be sticking up around the edges, install baseboards and shoe moldings, nailing them to the wall, not to the floor, and finish with transition strips between your new floor and other& ...


  • It turned out that laminate flooring was just what this homeowner was looking for, and he chose the Pergo Select brand of flooring in a “Smoked Oak” style. ... When it's time to install the floor, cut the tongues off the first row of planks. .... You can use your circular saw equipped with a carbide blade, but we recommend cutting from the back of the piece, especially if you have a net fit that will not be covered by base boards, such as against a shower stall or patio door.


  • For flawless wood floors, avoid these installation and finishing mistakes. ... When floorboards aren't acclimated or are exposed to lots of moisture, they can crush together and lift off the subfloor. When wood flooring becomes too .... If a mess has already been made, either by walking on the droplets or by allowing them to cure, then each droplet needs to be cut off the floor by hand with a razor blade before the entire floor is abraded in preparation for a fresh top coat.