deck post spacing in the UK

  • For Detail refer to the installation instruction for “Timber Fence post”. Jacksons Fencing Head Office Stowting Common Ashford Kent TN25 6BN. Tel 44 (0) 1233 . Fax 44 (0) 1233 www.jacksons-fencing.co.uk info jacksons-fencing.co.uk. You don't have to be a master carpenter to design & build a timber deck. Before doing any thing else decide what sort of deck best suits you and your home. Do you want it at ground level, elevated, or split level?


  • posts:: Joined: Tue Jul 24, 2007 9:12 am: Location: Somerset in the uk in Shepton mallet. Top& ...


  • FASCIA deck boards attached vertically to outer subframe for tidy appearance. HAND RAIL. BALUSTER. NEWEL post. BOTTOM RAIL. deckinG. FASCIA. JOIST. JOIST. JOIST. SUPPORT post. OVERSITE. SUPPORT post. FOOTinG ... and what furniture will be needed. If space is restricted you might think about building-in benches and storage planters. To help you think up what your deck will look like it's sometimes helpful to create a full size outline of the deck where you.


  • Leading suppliers of decking in the uk. Stocking a ... This calculator works out the joists at 500mm centres and nails are added pick 47 x 100 or 47 x 150 both will do the job but 47 x 150 is recommended if you are raising the deck from ground level . ... All screws are supplies. Handrails: Handrails are calculated with the newel posts at 2m centres. You will need to add one newel posts for every time there is a gap in your total length. Spindle are calculated with 100mm gap. deck Length.


  • The span of joists in the information below should only be taken as a guide. deck joist spacing will be determined by experience and knowledge, as well as the minimum spacings listed. They have been prepared from experience and also reference to Government Building Controls Data, and are based upon load bearings for floors to houses. The dimensions quoted are absolute maximum for decking joist spans and should not be exceeded. Where possible, and certainly on raised& ...


  • decking Subframe Design Guidance. decking Beam Span Guidance. We recommend beams are constructed from two 44 x 145mm Q-deck deck joists and are placed at maximum centres of 1.8m. in this instance the maximum span between deck post centres is 2.07m (C16) or 2.24m (C24). Cut away diagram of finished raise decking by Q-deck. Annotated decking diagram. Joist and deck Board spacing Guidance. The table below shows figures for domestic applications (uniformly& ...


  • install-decking-Step4. 3. Lay concrete slabs at the corner and centre points of the space you want to deck. The slabs provide a solid, load-spreading foundation for the deck and keep the wooden frame clear of the damp ground. Put a straight piece of wood on top of the slabs and check for level. Get the level as close as you can now by adding more slabs, if necessary. Other options for this foundation part of the job include concreting pressure-treated wooden posts in& ...


  • decking Joist spacing. The spacing between standard joists will depend upon the thickness of the actual deck boards. 28mm thick deckboards can be laid on joists with 600mm spacing - though for higher level decks, this should be reduced to 500mm centres. Composite deck boards ... Depending upon the height and size, the deck frame for a raised deck will be supported at intervals with joist bearers fixed to sturdy support posts that are concreted into the ground. The decking joist& ...


  • The post holes need to be 700mm deep and the decking posts are 100mm*100mm treated timber. deck post positions. The deck post holes need marking out. This can be difficult and can be made easier if you use some of the joists and put them into position. For the deck in this project we are spacing the joists at 400mm centre's. The decking posts need to be spaced at every metre in each direction. We have marked this onto the ledger and will temporarily screw a joist into position& ...


  • Use timber posts concreted into the ground to hold the structure in place. The decking design will depend on the space you have which is a result of how high above the ground the deck is to be. Where space allows use beams to support joists, for example, if your deck is 3.60m wide and you have created a framework supported with Timber posts and have fixed in place your 3.60m joists, then set at 450mm centres without additional support. At 3.60m long these joists& ...


  • Elevated decks can be free-standing or attached to a wall or side of a house. A qualified decking professional should be contacted for projects over 600mm. Structural posts of 100 x 100 x 1200mm should be used for raised/elevated decks. At least half the length of the post should be sunk into the ground and then fixed with concrete or alternatively concrete feet and dry cement can be used. Joists should be spaced at 400mm centres. Structural posts should be positioned no more than& ...


  • Laying a deck can improve the look and increase the usability of your garden, Use our handy how to guide to take you from start to finish the process of laying a deck. ... On soft ground it is possible to make a simple foundation of paving slabs bedded on gravel to support the deck and preserve the timber. Before you start laying ... Now mark, cut and fit the intermediate bearers, with a maximum spacing between bearers of 500mm, checking they are flat with a spirit level as you go. 12.


  • For conventional guard rail post installation, bolted to the side of the framing, larger framing will provide for more strength in the rails. For upper level decks 2x10 is recommended as the minimum size to use for strong guard post connections. 2x6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards. Similar to guards, if stairs are to be hung from the side of an upper-level deck, 2x10 as a minimum is recommended, as it will exceed the& ...


  • Attach 50 x 150mm rim joist to post using 7.0 x 100mm Rugged Structural Screw. Reinforce inside corners of rim joists with angle brackets attached with joist nails. Laying decking. Position deck boards so that ends overhang rim joists and space boards about 3mm apart to provide drainage. Attach decking by driving a pair of 60mm or 80mm (depending on the thickness of decking used) deck screws into each joist. Once the decking is down, snap a chalk line to mark straight cut-off& ...


  • How to install newel posts on a deck. ... Here again, as with the ledger we have used some stainless steel washers in order to space the newel post 10mm away from the wall. Ensure that the newel posts are level before fixing them in position by using a spirit level. deck hand rail. Here you can see that the newel posts have been bolted to the joist and that the deck boards have been cut out for the posts. The first decking board has been positioned so that it meets flush with a covering& ...


  • When installing posts or levelling the ground, take special care not to damage underground cabling, pipes or drainage, and do not permanently obstruct manhole covers or other services. fig-2.jpg. 2. Build a basic deck ... Secure the deck boards Once you are happy with the layout and spacing of the deck boards, fit and secure them to the bearers with 65mm (no.8 x 2½") decking screws, using two screws per board to each and every bearer to avoid cupping. Locate the screws about& ...


  • an idea of what groundworks you will need, if any, before building your deck and how materials and men will reach the site. 3. Sourcing Materials. Timber for use outside should be treated for exterior use. Timbers which are in contact with the ground (posts for instance) should be treated for ground contact. It sounds obvious but always check, interior treated timber will rot very quickly and may actually endanger people using the deck. decking should be grooved on top for grip and& ...